- QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS SERIAL NUMBER
- QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS UPDATE
- QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS DRIVER
- QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS DOWNLOAD
QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS DRIVER
Windows OSes usually apply a generic driver that allows systems to recognize the wireless component. Choose to select the location of the new driver manually and browse to the folder where you downloaded the driver About Wireless LAN Driver:
QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS UPDATE
Right click on the hardware device you wish to update and choose Update Driver Softwareģ. Go to Device Manager (right click on My Computer, choose Manage and then find Device Manager in the left panel)Ģ. In order to manually update your driver, follow the steps below (the next steps):ġ. (But I still lack a consistent quantification of this.The package provides the installation files for Qualcomm Atheros QCA9377 Adapter Wireless Driver version 12.0.0.116. I may have to dig a little deeper, because other devices seem to perform much better with the same router. Whether this was a quirk of the specific router, or just the bad state of Atheros Windows drivers, was never clear. I am running dual-boot Linux/Windows, and my recollection is that the QoS was disabled because, with it enabled, transfer speeds slowed to a trickle under Windows. HT is a required part of 802.11n, without it you get 11g speeds. Those last two lines suggest it's a misconfiguration on the router. ath10k_pci 0000:02:00.0 wlp2s0: disabling VHT as WMM/QoS is not supported by the AP ath10k_pci 0000:02:00.0 wlp2s0: disabling HT as WMM/QoS is not supported by the AP Modules linked in: snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic snd_hda_intel snd_intel_nhlt snd_hda_codec amdgpu(+) snd_hwdep snd_hda_core ath10k_pci snd_pcm snd_timer ath10k_core snd gpu_sched rtsx_pci ttm k10temp mfd_core ath soundcore ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 0 dfs 0 testmode 0 ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 Just for completeness, the output of 'dmesg | grep ath10k' is So I am just wondering if there are known or possible issues with this combination of kernel and firmware for this device. To be fair, I am running on an old-ish Verizon FIOS router, which AFAIK does not even support 802.11ac, but even 802.11n should be able to do better. I have had issues with Atheros speeds in the past, but these values strike me as dramatically below what should be expected.
QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS DOWNLOAD
Running speedtest-cli on this setup results in both upload and download speeds of 6-8 Mbit/s, Running speedtest on a tablet on the same network (with admittedly a different detected server) gives values 2-4 times as large.
QUALCOMM QCA9377 802.11AC WIRELESS ADAPTER AND FIOS QOS SERIAL NUMBER
Memory at e0200000 (64-bit, non-prefetchable) Ĭapabilities: Power Management version 3Ĭapabilities: MSI: Enable+ Count=1/8 Maskable+ 64bit-Ĭapabilities: Express Endpoint, MSI 00Ĭapabilities: Advanced Error ReportingĬapabilities: Device Serial Number 00-00-00-00-00-00-00-00Ĭapabilities: Latency Tolerance Reporting Subsystem: Lite-On Communications Inc QCA9377 802.11ac Wireless Network Adapterįlags: bus master, fast devsel, latency 0, IRQ 55 My laptop has an Atheros QCA9377 adaptor, with lspci -v outputĠ2:00.0 Network controller: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter (rev 31)
I am running a newly installed kernel, with /proc/version output I know this is a topic that comes up periodically. Posted: Sun 8:22 pm Post subject: Atheros wireless slow speeds Gentoo Forums Forum Index Kernel & Hardware
Gentoo Forums :: View topic - Atheros wireless slow speeds
0 kommentar(er)
